Phoenix RIF-1-RPT-LDP-24DC/2X21AU-relay module 2903330, a prefabricated relay module with in-line connection, including: relay base, multi-layer contact relay, plug-in display/interference suppression module and fixed bracket. Contact switching type: 2 changeover contacts. Input voltage: 24V DC
| Product Type |
Relay Module |
| Product Series |
RIFLINE complete |
| Application |
General |
| Mode of operation |
100% operating factor |
| mechanical life |
approx. 3x 107times |
| insulation characteristics |
| insulation |
input and output |
| changeover contacts |
| Overvoltage Category |
III |
| pollution level |
2 |
| Data Management Status |
| Last data maintenance date |
20.03.2025 |
| service life, electrical |
See Graph |
| rated conditions |
0.43W |
| test voltage (coil/contact) |
4 kVrms(50Hz,1 min, coil/contact) |
| test voltage (changeover contact/changeover contact) |
2.5 kVrms(50Hz,1 minute, changeover contact/changeover contact) |
| Rated overvoltage |
6 kV (input/output) |
| 4 kV (between changeover contacts) |
| coil side |
| Rated input voltage UN |
24V DC |
| Input Voltage Range |
19.2V DC ... 33.6V DC (20 °C) |
| to UNas reference |
See Graph |
| drives and functions |
monostable |
| drive (polarity) |
polarization |
| UN |
18 mA |
| Typical Response Time |
8 ms |
| Typical release time |
10 ms |
| coil voltage |
24V DC |
| protection circuit |
freewheeling diode |
| Operating voltage display |
yellow LED |
| switching |
| Contact Type |
2 changeover contacts |
| Switch Contact Type |
single contact |
| Contact Material |
AgNi, hard gold plating |
| maximum switching voltage |
30V AC |
| 36V DC |
| Minimum Switching Voltage |
100 mV (10 mA) |
| limit continuous current |
50 mA |
| Maximum impact current |
50 mA |
| minimum switching current |
1 mA (24 V) |
| Maximum power rating (resistive load) |
1.2W (24V DC) |
| Use Class CB Scheme (IEC 60947-5-1) |
AC15, 1.5 A/240V (N/O contact) |
| AC15, 2 A/250V (normally closed contact) |
| DC13, 2 A/24V (normally closed contact) |
| DC13, 0.2 A/250V (N/O contact) |
| switching: when the gold plating layer is destroyed |
| Considerations |
If the gold plating is damaged, the following values are applicable. |
| Contact Material |
AgNi |
| maximum switching voltage |
250V AC/DC |
| Minimum Switching Voltage |
5V (10 mA) |
| Maximum impact current |
25 A (20 ms, normally open contact) |
| minimum switching current |
10 mA (5 V) |
| Maximum power rating (resistive load) |
192W (24V DC) |
| 96W (available for 48V DC) |
| 60W (available for 60V DC) |
| 44W (available for 110V DC) |
| 57W (available for 220V DC) |
| 2000 VA (available for 250V AC) |
| switch capacity |
2 A (24V, DC13) |
| 0.2 A (at 110V, DC13) |
| 0.2 A (250V, DC13) |
| 2 A (24V, AC15) |
| 2 A (120V, AC15) |
| 2 A (250V, AC15) |
