Phoenix UNO-PS/1AC/48DC/60W-power supply 2902995, UNO POWER power supply for DIN rail installation, primary switching mode, input: 1 phase, output: 48V DC/60W
| AC operation | |
| Rated input voltage range | 100V AC ... 240V AC |
| Input Voltage Range | 85V AC ... 264V AC |
| AC input voltage range | 85V AC ... 264V AC |
| Supply Voltage | AC |
| Impulse current | < 30 A (typical) |
| impulse current integral (I2t) | < 0.5 A2s (typical) |
| frequency range (fN) | 50Hz ... 60Hz ± 10% |
| grid buffer time | > 20 ms (120V AC) |
| > 90 ms (230V AC) | |
| power consumption | Typical 1.3 A (100V AC) |
| Typical 0.6 A (240V AC) | |
| Rated power consumption | 134.7 VA |
| protection circuit | transient surge protection; varistor |
| power factor (cos phi) | 0.5 |
| Typical Response Time | < 1 s |
| input fuse | 2 A (slow fuse, internal) |
| recommend use | 6 A ... 16 A (characteristics B, C, D, K) |
| efficiency | Typical 89% (120V AC) |
| Typical 89% (230V AC) | |
| output characteristics | HICCUP |
| Rated output voltage | 48V DC |
| Rated output current (IN) | 1.25 A (-25°C ... 55 °C) |
| Attenuation | 55°C ... 70°C (2.5 %/K) |
| feedback voltage resistance | < 60V DC |
| output | ≤ 60V DC |
| control deviation | <1% (load change, static 10%... 90%) |
| <2% (dynamic load change 10%... 90%, 10Hz) | |
| < 0.1 % (input voltage variation is ± 10 %) | |
| residual wave | < 35 mVSS(rated value) |
| Short-circuit protection | is |
| output power | 60W |
| maximum no-load power consumption | < 0.4W |
| Maximum rated load power loss | < 7W |
| rise time | < 0.5 s (UOUT(10%... 90%)) |
| response time | < 2 ms |
| and connect | Yes, for redundancy and increased capacity |
| Concatenation | is |
| Input | |
| Connection Mode | screw connection |
| Minimum cross section of rigid conductor | 0.2 mm² |
| Maximum cross section of rigid conductor | 2.5 mm² |
| flexible lead | 0.2 mm² |
| Flexible lead maximum cross section | 2.5 mm² |
| Single conductor/flexible connection point, cold press head with plastic sleeve, minimum | 0.2 mm² |
| Single wire/flexible connection point, cold press head with plastic sleeve, maximum | 2.5 mm² |
| single-conductor/flexible connection point, cold press head without plastic sleeve, minimum | 0.2 mm² |
| Single wire/flexible connection point, cold press head with plastic sleeve, maximum | 2.5 mm² |
| Minimum Wire Cross Section AWG | 24 |
| Maximum conductor cross section AWG | 14 |
| stripping length | 8mm |
| thread | M3 |
| Minimum tightening torque | 0.5 Nm |
| Maximum tightening torque | 0.6 Nm |
| Output | |
| Connection Mode | screw connection |
| Minimum cross section of rigid conductor | 0.2 mm² |
| Maximum cross section of rigid conductor | 2.5 mm² |
| flexible lead | 0.2 mm² |
| Flexible lead maximum cross section | 2.5 mm² |
| Single conductor/flexible connection point, cold press head with plastic sleeve, minimum | 0.2 mm² |
| Single wire/flexible connection point, cold press head with plastic sleeve, maximum | 2.5 mm² |
| single-conductor/flexible connection point, cold press head without plastic sleeve, minimum | 0.2 mm² |
| Single wire/flexible connection point, cold press head with plastic sleeve, maximum | 2.5 mm² |
| Minimum Wire Cross Section AWG | 24 |
| Maximum conductor cross section AWG | 14 |
| stripping length | 8mm |
| thread | M3 |
| Minimum tightening torque | 0.5 Nm |
| Maximum tightening torque | 0.6 Nm |
Phoenix UNO-PS/1AC/48DC/ 60W-Power 2902995
