Phoenix CAPAROC E1 12-24DC/1-10A-Electronic equipment circuit breaker 1115649, a single-channel electronic circuit breaker module, used to protect 12V and 24V DC loads in the event of overload and short circuit. The rated current can be adjusted between 1 A and 10 A via the LED button. Suitable for DIN rail mounting via CAPAROC bus bars.
Product Type
Equipment circuit breaker
Product Series
CAPAROC
type
Plug-in Modules
Bits
1
Channels
1
slots
1
insulation characteristics
protection level
III
pollution level
2
Overview
working voltage
10V DC ... 30V DC
Rated voltage
12V DC
24V DC
Nominal operating current IN
10 A DC (per channel)
Nominal operating current IN
1 / 2 / 3 / 4 / 5 / 6 / 7 / 8/9/10 A DC (each output channel is adjustable)
Rated current (pre-adjusted)
4 A
Rated overvoltage
0.5 kV
Breaking method
E (Electronic)
required spare fuse
only in I of the power supplymax> Short circuit switching capacity when required. Built-in fail-safe element.
Short-circuit switch capacity
300 A
dielectric strength
35V DC (load circuit)
Fuse
electronic
efficiency
> 99%
closed-circuit current I0
Typical 8.5 mA (no load at 24V)
power consumption
Typical 0.2W (no load at 24V)
< 1.6W (in normal operation at 24V and 10 A)
Measurement Tolerance I
± 15% (typical)
temperature attenuation
10 A (total current at 40°C)
7 A (total current at 65°C)
MTBF (IEC 61709, SN 29500)
18685596 h (25°C, 21% load)
7871572 h (40°C at 34.25% load)
1102033 h (at 40°C, 100% load)
voltage drop
0.14V (at 10 A)
fail-safe components
15 A DC (per output channel)
Contact Type
without electrical isolation
Load Circuit
Downtime
4 s (for overload 1.1…1.5 x IN)
1 s (for overload 1.5…2.0 x IN)
0.1 s (for overload 2.0…3.0 x IN)
Typical 10 ms (for short circuit> 3.0 x IN)
undervoltage shutdown
≤ 8.5V DC (active)
≥ 9.2V DC (passive)
Overvoltage shutdown
≥ 32.5V DC (active)
≤ 30.5V DC (passive)
Maximum capacitive load
≤ 20000 & micro;F (depending on current setting and available short-circuit current)
impact suppression
50 ms (works with CAPAROC PM IOLs and CAPAROC PM PN power modules)
fuse protection output
Connection Mode
in-line connection
stripping length
10mm
Flexible Wire Cross Section
0.2 mm² ... 4 mm²
Rigid conductor cross section
0.2 mm² ... 4 mm²
Attachable Guide Cross Section AWG
24 ... 12
Flexible conductor cross-section, with sleeve, with plastic insulation sleeve
0.25 mm² ... 4 mm²
flexible conductor cross-section with cold press head without insulation sleeve
0.25 mm² ... 4 mm²
Channel LED Off
Off (channel closed)
Channel LED Yellow
flashing (channel on, channel load> 80%)
flashing (programming mode active)
flashes twice (check installation, no communication with power module)
Channel LED Green
flashing (channel on)
Channel LED Red
flashing (channel off, overvoltage or undervoltage active)
ON temporarily (channel shutdown, 5 s cooling phase, overload or short circuit release)
flashing (channel closed, ready to reconnect, overload or short circuit release)
