Phoenix PS-EE-2G/1AC/24DC/75W/SC-power 1234301, primary switching power supply, ESSENTIAL POWER, screw connection, DIN rail installation, input: 1 phase, output: 24V DC / 3.125 A, adjustable range 24V DC ... 28V DC
AC operation
Power System Configuration
TN,TT,IT (PE)
Rated input voltage range
100V AC ... 240V AC
Input Voltage Range
110V AC ... 240V AC ±10 % (PN= 75 W)
100V AC ... 109V AC -15 % ... +10 % (PN= 63 W)
National Grid Typical Voltage
120V AC
230V AC
Supply Voltage
AC
Impulse current
Typical 27 A (at 25°C)
impulse current integral (I2t)
Typical 0.6 A2s
frequency range (fN)
50Hz ... 60Hz ± 10%
grid buffer time
Typical 14 ms (120V AC)
Typical 70 ms (230V AC)
power consumption
Maximum 1.5 A (75W)
Maximum 1.5 A (63W)
Typical 1.3 A (110V AC (75W))
Typical 0.75 A (240V AC (75W))
Typical 1.2 A (100V AC (63W))
Typical 1.1 A (109V AC (63W))
protection circuit
transient protection; varistor
Suction time
Typical 1 s
Device power fuse
3.15 A built-in (equipment protection) fast fuse
recommend use
6 A ... 16 A (characteristics B, C, D, K or similar)
PE discharge current
< 3.5 mA
efficiency
typical (120V AC)
Typical 89% (230V AC)
Rated output voltage
24V DC
output voltage (USet) setting range
24V DC ... 28V DC (> 24V DC, stable capacity limit)
Rated output current (IN) (IN_PMax)
maximum 3.125 A (PN= 75 W)
Rated output current (IN) (IN_PMin)
maximum 2.62 A (PN= 63 W)
Short-circuit protection
is
Anti-aircraft turn
is
amplitude factor
Typical 3 (120V AC)
Typical 4 (230V AC)
output power (PN)
75W (240V AC)
63W (100V AC)
and connect
Yes, increased power and increased redundancy using diodes
Concatenation
Yes, for higher output voltages
feedback voltage resistance
≤ 35V DC
output
≤ 35V DC
residual wave
Typical 50 mVSS(rated value)
control deviation
<2% (load change, static 10%... 90%)
<4% (load change, dynamic 10%... 90%)
< 0.1 % (input voltage variation is ± 10 %)
rise time
< 100 ms (UOut= 10%... 90%)
minimum no-load power consumption
< 1W (120V AC)
maximum no-load power consumption
< 1W (230V AC)
minimum rated load power consumption
< 11W (120V AC)
Maximum rated load power loss
< 9W (230V AC)
Built-in fuse protection
No
Input
Location
1.x
identification
1.1 (),1.2 (L),1.3 (N)
Wire Connection
Connection Mode
screw connection
Rigidity
0.5 mm² ... 2.5 mm²
flexibility
0.5 mm² ... 2.5 mm²
flexible strip cold press head without plastic sleeve
0.5 mm² ... 2.5 mm²
flexible strip cold press head with plastic sleeve
0.5 mm² ... 2.5 mm²
Rigid (AWG)
20 ... 14 (Cu)
stripping length
6.5mm
Tightening torque
0.5 Nm ... 0.6 Nm
5 lbf-in. ... 7 lbf-in.
Screw head drive mode
slotting L
Output
Location
2.x
identification
2.1,2.2 (+),2.3,2.4 (-)
Wire Connection
Connection Mode
screw connection
Rigidity
0.5 mm² ... 2.5 mm²
flexibility
0.5 mm² ... 2.5 mm²
flexible strip cold press head without plastic sleeve
0.5 mm² ... 2.5 mm²
flexible strip cold press head with plastic sleeve
