Phoenix PSI-MOS-PROFIB/FO 660 T-FO converter 2708287, fiber optic converter, built-in optical diagnosis function, alarm contact, for PROFIBUS up to 12 Mbps, T-coupler with two optical fiber interfaces (FSMA),660 nm, Suitable for polymer fiber/PCF fiber optic cable
| Product Type |
Media Converter |
| Product Series |
PSI-MOS |
| MTTF |
213 years (SN 29500 standard, temperature 25°C, duty cycle 21%) |
| 150 years (SN 29500 standard, temperature 40°C, duty cycle 34.25%) |
| 86 years (SN 29500 standard, temperature 40°C, duty cycle 100%) |
| MTBF |
201 years (Telcordia standard, temperature 25°C,21% operation cycle (5 days a week, 8 hours a day)) |
| 42 years (Telcordia standard, 40°C,34.25% cycle (12 hours a day, 5 days a week)) |
| electrical isolation |
VCC // RS-485 |
| rated conditions |
2.4W |
| test voltage data interface/power supply |
1.5 kVrms(50 Hz,1 min) |
| Power |
| Supply Voltage Range |
18V DC ... 30V DC (via plug-in COMBICON screw terminal block) |
| Rated supply voltage |
24V DC (UL compliant) |
| Typical current consumption |
100 mA (24V DC) |
| Maximum current consumption |
130 mA |
| ≤ 2 A (via DIN rail connector when running in connection site) |
| switching |
| Output Name |
relay output |
| Output Description |
Alarm output |
| outputs |
1 |
| maximum switching voltage |
60V DC (resistive load, universal load) |
| 30V AC (resistive load) |
| 42V AC (peak, resistive load) |
| limit continuous current |
0.46 A |
| Power |
| Connection Mode |
plug-in COMBICON screw terminal block |
| stripping length |
7.00mm |
| Tightening torque |
0.56 Nm ... 0.79 Nm |
| -bit distortion, input |
± 35% (allowed) |
| -bit distortion output |
< 6.25% |
| bit delay |
< 1 Bit (DIP 7 = OFF, standard run) |
| 11 Bit (DIP 7 = ON, redundant operation) |
| signal |
PROFIBUS |
| data: optical fiber |
| Channels |
2 |
| minimum transmission power |
-3 dBm (980/1000 µm) |
| -15.4 dBm (200/230 µm) |
| transmission length, including 3 dB system margin |
70 m (F-P 980/1000 230 dB/km with quick-mount connector) |
| 400 m (F-K 200/230 10 dB/km with quick-mount connector) |
| Transfer Protocol |
RS-485 interface, protocol transparency |
| Connection Mode |
F-SMA |
| wavelength |
660 nm |
| Minimum Receiving Sensitivity |
-30 dBm |
| receiver |
-3 dBm (980/1000 µm) |
| transmission medium |
Polymeric Fiber |
| PCF fiber |
| Data: PROFIBUS according to IEC 61158, RS-485 2-wire, half-duplex, automatic control |
| serial transmission rate |
≤ 12 Mbps |
| Connection Mode |
D-SUB-9 female connector |
| Transmission Length |
≤ 1200 m (depending on rate, shielded twisted pair) |
| single wire/wiring point, rigid |
0.2 mm² ... 2.5 mm² |
| single wire/wiring point, flexible |
0.2 mm² ... 2.5 mm² |
| AWG stranded wire, flexible |
14 |
| AWG Wire Minimum Cross Section, Flexible |
24 |
| single wire/wiring point, maximum rigid AWG |
14 |
| Single Wire/End Point, Minimum Rigid AWG |
24 |
| transmission medium |
copper cable |
| File Format/Encoding |
UART(11Bit,NRZ) |
| data direction switching |
automatic control |
| Rated output voltage |
5V ±0.25 (50 mA) |
