Phoenix ESSENTIAL-PS/3AC/24DC/480W/EE-power 1018299,ESSENTIAL edition power supply, primary switch mode, for DIN rail installation, input: 3 phase, output: 24V DC/480W
| AC operation |
| Rated input voltage range |
3x 400V AC ... 500V AC |
| Input Voltage Range |
3x 320V AC ... 575V AC (attenuation <360V AC: 1.5 %/V) |
| operation |
3x 320V AC ... 575V AC (attenuation <360V AC: 1.5 %/V) |
| AC input voltage range |
3x 320V AC ... 575V AC (attenuation <360V AC: 1.5 %/V) |
| 2x 360V AC ... 575V AC (2-phase system) |
| Supply Voltage |
AC |
| Impulse current |
< 15 A |
| impulse current integral (I2t) |
0.5 A2s |
| AC frequency range |
45Hz ... 65Hz |
| grid buffer time |
> 17 ms (3x 400V AC) |
| power consumption |
3x 1.1 A (400V AC) |
| 3x 0.8 A (480V AC) |
| Rated power consumption |
666.33 VA |
| protection circuit |
transient surge protection; varistor |
| power factor (cos phi) |
0.67 |
| Typical Response Time |
< 1 s |
| Allowable Spare Fuses |
B6 B10 B16 |
| recommend use |
6 A ... 16 A |
| PE discharge current |
< 3.5 mA |
| efficiency |
91% (at 400V AC and rated) |
| output characteristics |
U/ I |
| Rated output voltage |
24V DC ±1% |
| output voltage (USet) setting range |
22.5V DC ... 29.5V DC (> 24V DC, stable capacity limit) |
| Rated output current (IN) |
20 A (UOUT= 24V DC) |
| Attenuation |
55°C ... 70°C (2.5 %/K) |
| feedback voltage resistance |
35V DC |
| output |
< 35V DC |
| Maximum capacitive load |
Unlimited |
| Active Current Limit |
about 25 A |
| control deviation |
<1% (load change, static 10%... 90%) |
| <2% (change of load, dynamic 10%... 90%) |
| < 0.1 % (input voltage variation is ± 10 %) |
| residual wave |
< 10 mVSS |
| Short-circuit protection |
is |
| Anti-aircraft turn |
is |
| output power |
480W |
| peak switching voltage rated load |
< 30 mVSS |
| maximum no-load power consumption |
< 6W |
| Maximum rated load power loss |
< 48W |
| rise time |
< 2 ms (UOUT(10%... 90%)) |
| Concurrent |
Yes, for redundancy and increased capacity |
| Concatenation |
is |
| Input |
| Connection Mode |
screw connection |
| Minimum cross section of rigid conductor |
0.2 mm² |
| Maximum cross section of rigid conductor |
2.5 mm² |
| Minimum cross section of flexible lead |
0.2 mm² |
| Flexible lead maximum cross section |
2.5 mm² |
| Minimum Wire Cross Section AWG |
24 |
| Maximum conductor cross section AWG |
14 |
| stripping length |
9mm |
| thread |
M2,5 |
| Minimum tightening torque |
0.4 Nm |
| Maximum tightening torque |
0.5 Nm |
| Output |
| Connection Mode |
screw connection |
| Minimum cross section of rigid conductor |
0.5 mm² |
| Maximum cross section of rigid conductor |
6 mm² |
| Minimum cross section of flexible lead |
0.5 mm² |
| Flexible lead maximum cross section |
4 mm² |
| Minimum Wire Cross Section AWG |
12 |
| Maximum conductor cross section AWG |
10 |
| stripping length |
14mm |
| thread |
M3 |
| Minimum tightening torque |
0.5 Nm |
| Maximum tightening torque |
0.6 Nm |
| Signal Type |
LED |
| Operating voltage display |
Green LED |
| signal output |
| Status Display |
DC OK LED green |
| Notes on Status Display |
UOutput>21.5V: LED on |
